USP LUMBER CONNECTORS

Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes.TRIPLE ZINC18 GaugeWdth x Lgth In=1-1/4 x 18GALVANIZED STEELUnit: EA ...

Requires 10d nails for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes.TRIPLE ZINC18 GaugeWdth x Lgth In=1-1/4 x 18GALVANIZED STEELUnit: EA

These post bases allow installers to pre-align posts and preset post heights above concrete floors or footings. By eliminating post-to-concrete contact, moisture damage is reduced. Elevated post...

These post bases allow installers to pre-align posts and preset post heights above concrete floors or footings. By eliminating post-to-concrete contact, moisture damage is reduced. Elevated post bases are ideal for building carports, decks or porches. All Series feature convenient nail fastening to post.TRIPLE ZINC16 Gauge U-BracketPost Size In=4 x 4STEELUnit: EA

Designed for medium load conditions. Extended 3 in deep seat provides enhanced truss bearing.16 Gauge - 1-5/8"W x 3"DJoist Size=2 x 6-8Ht In=5-7/16GALVANIZED STEEL - SLANT NAILUnit: EA ...

Designed for medium load conditions. Extended 3 in deep seat provides enhanced truss bearing.16 Gauge - 1-5/8"W x 3"DJoist Size=2 x 6-8Ht In=5-7/16GALVANIZED STEEL - SLANT NAILUnit: EA

The CPB is made of corrosion-resistant composite material compatible with preservative treated lumber. Provides code required 1 in stand-off and can be used with rough lumber sizes.Post Size In=4 x...

The CPB is made of corrosion-resistant composite material compatible with preservative treated lumber. Provides code required 1 in stand-off and can be used with rough lumber sizes.Post Size In=4 x 4Wdth In=3-1/4COMPOSITE MATERIALUnit: EA

Two-piece design. Two extended side plates and wraparound post design offers greater lateral resistance. Easy retrofit installations. Designed to work with single, solid-sawn beams, but can be used...

Two-piece design. Two extended side plates and wraparound post design offers greater lateral resistance. Easy retrofit installations. Designed to work with single, solid-sawn beams, but can be used with built-up beams. Triple zinc finish for ACQ pressure-treated lumber. Requires 16d HDG fasteners for installation. Meets ICC-ES ESR-1781, FL13285 and L.A. City RR25843 codes. 18 ga - 1-7/16 in W x 2-5/16 in H1 x 2-3/16 in H2 x 3-9/16 in L1 x 6-1/2 in L2.Post Size In=6 x 6Finish=G90STEELUnit: EA ...

Use for joist to header, rafter to plate, stud to plate or 1 in foam board installations. Achieves continuous load path in high wind and seismic resistant construction. Enables quick field...

Use for joist to header, rafter to plate, stud to plate or 1 in foam board installations. Achieves continuous load path in high wind and seismic resistant construction. Enables quick field adjustments for 2 and 3-way connections. Tabs enable two and three-way connections. Bend tabs only once. Requires 8d x 1-1/2 nails. Meets SBCCI, BOCA - NER 505, ICBO 5736, DSA PA-076, Dade County, FL 01-417.11 and L.A. City RR25303 codes. For additional information including allowable loads and number of...

Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly, no load ratings assigned. G90 galvanizing finish. 22 ga.Wdth x Lgth...

Prong plates with straight prongs. Joins flat surfaces of 2 or more wood members. Not for structural use OR use in truss assembly, no load ratings assigned. G90 galvanizing finish. 22 ga.Wdth x Lgth In=13/16 x 3-1/2GALVANIZED STEEL - PRONGUnit: EA

Connects stud to single or double plates. G90 galvanized finish. Requires 12 10d x 1-1/2 nails. Meets ICC-ES ESR-1881, FL821 and L.A. City RR25779 codes.TRIPLE ZINC18 Gauge - 3-9/16"W x 1-1/4"LHt...

Connects stud to single or double plates. G90 galvanized finish. Requires 12 10d x 1-1/2 nails. Meets ICC-ES ESR-1881, FL821 and L.A. City RR25779 codes.TRIPLE ZINC18 Gauge - 3-9/16"W x 1-1/4"LHt In=8-5/8GALVANIZED STEELUnit: EA

Offers double shear nailing. Dimples on hanger allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing. G90 galvanizing finish. Requires 16d nails for...

Offers double shear nailing. Dimples on hanger allow for 30 to 45 degree nailing through joist into header, resulting in higher loads and less nailing. G90 galvanizing finish. Requires 16d nails for installation. Meets ICC-ES ESR-1881, FL821, L.A. City RR25779 and Dade County, FL06-0921.05 codes.16 Gauge - 1-5/8"W x 2"DJoist Size=2 x 8-10Ht In=7-3/16GALVANIZED STEEL - SLANT NAILUnit: EA

For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting...

For general-purpose reinforcements of many framing connections. G185 galvanized finish. Can be used in both new construction and retrofit applications. Staggered nail patterns reduce wood splitting and allows installation on both sides of the supported member. Triple zinc clips require 10d HDG or 16d HDG nails. Meets ICC-ES ESR-2104, FL820 and L.A. City RR25745 codes.1-5/16"W1 x 2-3/8"W2 x 6-15/16"L - 16 GAUGEFinish=Triple ZincSTEELUnit: EA ...

The JUS hanger Series offers double shear nailing. USP's dimple allows for 30 to 45 deg nailing through the joist into the header resulting in higher loads and less nailing. Slant/double shear...

The JUS hanger Series offers double shear nailing. USP's dimple allows for 30 to 45 deg nailing through the joist into the header resulting in higher loads and less nailing. Slant/double shear nailing allows for higher load values, fewer nails and faster installation.TRIPLE ZINC FOR ACQ PRESSURE TREATED LUMBER18 Gauge - 3-5/8"W x 2"DJoist Size In=4 x 6Ht In=5SINGLE 2X'S - STEEL - SLANT NAILUnit: EA

The JDS purlin hangers provide a convenient, flexible solution when attaching purlins together.G90 GALVANIZING20 GaugeWdth x Ht In=1-9/16 x 3-1/2GALVANIZED STEELSINGLE-SIDEPURLIN HANGERSUnit: EA ...

The JDS purlin hangers provide a convenient, flexible solution when attaching purlins together.G90 GALVANIZING20 GaugeWdth x Ht In=1-9/16 x 3-1/2GALVANIZED STEELSINGLE-SIDEPURLIN HANGERSUnit: EA

Wide strapping. Requires 16 WS15-HDG nails for installation. Meets 110 codes.TRIPLE ZINC12 GaugeWdth x Lgth In=3-1/4 x 16GALVANIZED STEELUnit: EA ...

Wide strapping. Requires 16 WS15-HDG nails for installation. Meets 110 codes.TRIPLE ZINC12 GaugeWdth x Lgth In=3-1/4 x 16GALVANIZED STEELUnit: EA

Deck collapses are often caused by failure of the connection where the deck is attached to the main structure due to little or no lateral capacity. ADTT-TZ is an adjustable deck tension tie designed...

Deck collapses are often caused by failure of the connection where the deck is attached to the main structure due to little or no lateral capacity. ADTT-TZ is an adjustable deck tension tie designed to effectively transfer the out of plane lateral loads of the deck to the house structure.Unit: EA

These post bases allow installers to pre-align posts and preset post heights above concrete floors or footings. By eliminating post-to-concrete contact, moisture damage is reduced. Elevated post...

These post bases allow installers to pre-align posts and preset post heights above concrete floors or footings. By eliminating post-to-concrete contact, moisture damage is reduced. Elevated post bases are ideal for building carports, decks or porches. All Series feature convenient nail fastening to post.USP PRIMER14 Gauge U-BracketPost Size In=4 x 4STEELUnit: EA

IHFL (18 ga) and IHF (16 ga) series face mount hangers feature speed prongs for temporary placement and seat cleats to grab the bottom flange of the supported I-joist. Diamond holes in header and...

IHFL (18 ga) and IHF (16 ga) series face mount hangers feature speed prongs for temporary placement and seat cleats to grab the bottom flange of the supported I-joist. Diamond holes in header and joist allow for optional Max nailing for customized fastening to match allowable load needed. Install nails in all fastener holes when the Max allowable load is needed while lighter load capacities can be achieved with a quick installation of round holes only, saving you time and money on the...

For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. One piece, designed to work with single, solid sawn beams, but can be used with build-up...

For light-duty post-to-beam connections. Quick and easy installation on decks, carports and other projects. One piece, designed to work with single, solid sawn beams, but can be used with build-up beams made of 2x lumber and shims fastened together to act as a unit. Requires 16d HDG nails for installation. Meets ICC-ES ESR-1280, FL11664, L.A. City RR25749 and Dade County, FL 07-0306.06 codes. For additional information including allowable loads and number of fasteners, please see USP Lumber...

Prong plates with angled, hammer-in prongs. Joins flat surfaces of 2 or more wood members. G90 galvanizing finish. Not intended for structural use OR in truss assembly. No load ratings assigned. 18...

Prong plates with angled, hammer-in prongs. Joins flat surfaces of 2 or more wood members. G90 galvanizing finish. Not intended for structural use OR in truss assembly. No load ratings assigned. 18 ga.Wdth x Lgth In=1-1/2 x 4GALVANIZED STEEL - PRONGUnit: EA

Snap-on, no-nail bridging can be placed in existing floor systems where joist movement is suspected. Two-piece construction creates a solid diagonal brace against joist movement.Joist Spacing...

Snap-on, no-nail bridging can be placed in existing floor systems where joist movement is suspected. Two-piece construction creates a solid diagonal brace against joist movement.Joist Spacing OC=16SNAP-ONGALVANIZED STEELUnit: EA

Post anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1 in stand-off plate to elevate wood posts above concrete...

Post anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1 in stand-off plate to elevate wood posts above concrete surfaces as required by building code.16 GAUGE STAND-OFF PLATE - 18 GAUGE BASE3-9/16"W x 3-1/2"H x 3-1/2"LPost Size In=4 x 4Finish=Trp. Zinc2-SIDED - HIGH CAPACITY - STEELUnit: EA

Used to tie first and second story framing together, anchor studs to foundations or to tie purlins to masonry or concrete. Features self-jigging, formed design with code required distances built-in....

Used to tie first and second story framing together, anchor studs to foundations or to tie purlins to masonry or concrete. Features self-jigging, formed design with code required distances built-in. Requires 7/8 in, 5/8 and 3/4 in bolts for installation. Meets IAPMO-ES ER-0200 and FL14500 codes.Triple Zinc12 Gauge - 5/8" BoltsWxHxD In=2-1/16 x 8-1/8 x 2-3/4STEELUnit: EA

Post anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1 in stand-off plate to elevate wood posts above concrete...

Post anchors are used to secure wood posts to concrete footings. These post anchors also provide moisture damage protection and feature a 1 in stand-off plate to elevate wood posts above concrete surfaces as required by building code.12 GAUGE STAND-OFF & WASHER - 18 GAUGE BASE - DISPLAY PACK5-9/16"W x 3-1/2"H x 5-1/2"LPost Size In=6 x 6Finish=Triple Zinc4-SIDED - HIGH CAPACITY - STEELUnit: EA

IHFL (18GA) and IHF (16GA) series face mount hangers feature speed prongs for temporary placement and seat cleats to grab the bottom flange of the supported I-joist. Diamond holes in header and...

IHFL (18GA) and IHF (16GA) series face mount hangers feature speed prongs for temporary placement and seat cleats to grab the bottom flange of the supported I-joist. Diamond holes in header and joist allow for optional Max nailing for customized fastening to match allowable load needed. Install nails in all fastener holes when the Max allowable load is needed while lighter load capacities can be achieved with a quick installation of round holes only, saving you time and money on the jobsite.16...

These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.18 GAUGE - 1-1/4"W x 7-13/16"HFinish=G90DOUBLE PLATE - STEELUnit:...

These anchors tie trusses and rafters to top plates and may be used to tie wood framing members to resist uplift and lateral forces.18 GAUGE - 1-1/4"W x 7-13/16"HFinish=G90DOUBLE PLATE - STEELUnit: EA