KNAPE & VOGT MFG

Use with #129 rubber cushion. For 1/4 in Dia holes x 3/8 in L pin.Unit: EA

Use with #129 rubber cushion. For 1/4 in Dia holes x 3/8 in L pin.Unit: EA

Double-lug bracket design prevents shelves and contents from falling when bumped. Supports adjust to accommodate changes in storage and layout. Rounded corners and recessed groove design. Cover...

Double-lug bracket design prevents shelves and contents from falling when bumped. Supports adjust to accommodate changes in storage and layout. Rounded corners and recessed groove design. Cover strips conceal screw holes and slots for a more refined appearance. Epoxy finish is resistant to chips and scratches.Unit: EA

Medium-duty, precision slides for box drawer or pedestal file drawers up to 24 in wide. For frame and frameless construction. May be used horizontal position with a reduced load rating of 30 lb....

Medium-duty, precision slides for box drawer or pedestal file drawers up to 24 in wide. For frame and frameless construction. May be used horizontal position with a reduced load rating of 30 lb. Height of 1-13/16 in, required clearance of 1/2 in plus 1/32 in minus 0 each side. Features telescoping, full extension on precision steel ball bearings. 32 mm hole pattern with direct access mounting. Lever disconnect for easy drawer removal. Ball retainer latch and ramps, for easy drawer insertion....

3/4 in steel strut and 5 mm thick steel bar construction. Tough epoxy coat finish. Recommended fasteners are 3 in or longer 5/16 in pan head screws mounted onto studs. Attach shelf using #8 or...

3/4 in steel strut and 5 mm thick steel bar construction. Tough epoxy coat finish. Recommended fasteners are 3 in or longer 5/16 in pan head screws mounted onto studs. Attach shelf using #8 or larger rounded-head wood screw. Holds up to 1200 lb per pair when mounted per manufacturer recommendations. Mounts directly to wall. Less fasteners.Unit: EA

Add drama to your collectibles display. The 36 x 8-1/2 in shelf is secured to the wall with a concealed steel bracket for strength and holds 30 lb when properly mounted.Unit: EA

Add drama to your collectibles display. The 36 x 8-1/2 in shelf is secured to the wall with a concealed steel bracket for strength and holds 30 lb when properly mounted.Unit: EA

Light-duty slide designed for general drawer applications. Mounts with staples or screws. Height of 1 in. Required Clearance:1/8 in each side, 1-1/2 in from rear of drawer to cabinet, drawer to be...

Light-duty slide designed for general drawer applications. Mounts with staples or screws. Height of 1 in. Required Clearance:1/8 in each side, 1-1/2 in from rear of drawer to cabinet, drawer to be 3/8 in shallower than opening. High-density polyethylene rollers. Drawers lift out for easy removal. Packaged with screws and installation instructions.Unit: EA

Medium-duty, precision slides for box drawer or pedestal file drawers up to 24 in wide. For frame and frameless construction. May be used horizontal position with a reduced load rating of 30 lb....

Medium-duty, precision slides for box drawer or pedestal file drawers up to 24 in wide. For frame and frameless construction. May be used horizontal position with a reduced load rating of 30 lb. Height of 1-13/16 in, required clearance of 1/2 in plus 1/32 in minus 0 each side. Features telescoping, full extension on precision steel ball bearings. 32 mm hole pattern with direct access mounting. Lever disconnect for easy drawer removal. Ball retainer latch and ramps, for easy drawer insertion....

3/4 in steel strut and 5 mm thick steel bar construction. Tough epoxy coat finish. Recommended fasteners are 3 in or longer 5/16 in pan head screws mounted onto studs. Attach shelf using #8 or...

3/4 in steel strut and 5 mm thick steel bar construction. Tough epoxy coat finish. Recommended fasteners are 3 in or longer 5/16 in pan head screws mounted onto studs. Attach shelf using #8 or larger rounded-head wood screw. Holds up to 1200 lb per pair when mounted per manufacturer recommendations. Mounts directly to wall. Less fasteners.Unit: EA

Snaps securely into place. For use with #233 and #255. High-strength steel construction.Unit: EA

Snaps securely into place. For use with #233 and #255. High-strength steel construction.Unit: EA

Screws are 1-1/2 in long with a #8 body and #6 head.Unit: BAG

Screws are 1-1/2 in long with a #8 body and #6 head.Unit: BAG

Knape & Vogt 255-81N Standard Nail, Zinc, Bright, Suitable for: 233 and 255 Series Steel Pilaster StandardsUnit: PK650

Knape & Vogt 255-81N Standard Nail, Zinc, Bright, Suitable for: 233 and 255 Series Steel Pilaster StandardsUnit: PK650

For use with the 80 Series standards. For shelving applications in light industrial, commercial and residential use. Standards can be mounted to nearly any type of wall. For storage and display...

For use with the 80 Series standards. For shelving applications in light industrial, commercial and residential use. Standards can be mounted to nearly any type of wall. For storage and display applications in retail stores, grocery stores, light warehouses, repair garages, maintenance storage, business office storage and residential storage. Reinforced brackets lock into slotted standards for strong, secure weight-bearing support. Fully adjustable in 1 in increments. 16 ga cold rolled steel...

Double-lug bracket design prevents shelves and contents from falling when bumped. Supports adjust to accommodate changes in storage and layout. Rounded corners and recessed groove design. Cover...

Double-lug bracket design prevents shelves and contents from falling when bumped. Supports adjust to accommodate changes in storage and layout. Rounded corners and recessed groove design. Cover strips conceal screw holes and slots for a more refined appearance. Epoxy finish is resistant to chips and scratches.Unit: EA

John Sterling Heavyweight diamond plate shelving and pegboard system is built to withstand the tough demands of workshop or garage.Unit: EA

John Sterling Heavyweight diamond plate shelving and pegboard system is built to withstand the tough demands of workshop or garage.Unit: EA

Use with #129 rubber cushion. For 1/4 in Dia holes x 3/8 in L pin.Unit: BAG12

Use with #129 rubber cushion. For 1/4 in Dia holes x 3/8 in L pin.Unit: BAG12

Joint fastener designed for 3/4 in wood. Center-to-center 2 to 3-1/2 in. Applies an even, controlled pressure between joint members to eliminate twisting and buckling. Zinc finish.Unit: EA

Joint fastener designed for 3/4 in wood. Center-to-center 2 to 3-1/2 in. Applies an even, controlled pressure between joint members to eliminate twisting and buckling. Zinc finish.Unit: EA

Designed for medium duty applications where a lever release is desired. For kitchen cabinet, vanity, desk and store fixture applications. Height of 3 in. Required clearance of 1/2 in plus 1/32 in...

Designed for medium duty applications where a lever release is desired. For kitchen cabinet, vanity, desk and store fixture applications. Height of 3 in. Required clearance of 1/2 in plus 1/32 in minus 0 each side. Features Positive stop lever that prevents accidental drawer removal. Zinc-plated cold rolled steel. Ball bearing nylon rollers. Packaged with screws and installation instructions. Maximum drawer width 18 in.Unit: SET

Designed for medium duty applications where a lever release is desired. For kitchen cabinet, vanity, desk and store fixture applications. Height of 3 in. Required clearance of 1/2 in plus 1/32 in...

Designed for medium duty applications where a lever release is desired. For kitchen cabinet, vanity, desk and store fixture applications. Height of 3 in. Required clearance of 1/2 in plus 1/32 in minus 0 each side. Features Positive stop lever that prevents accidental drawer removal. Zinc-plated cold rolled steel. Ball bearing nylon rollers. Packaged with screws and installation instructions. Maximum drawer width 18 in.Unit: SET

For use with the 80 Series standards. For shelving applications in light industrial, commercial and residential use. Standards can be mounted to nearly any type of wall. For storage and display...

For use with the 80 Series standards. For shelving applications in light industrial, commercial and residential use. Standards can be mounted to nearly any type of wall. For storage and display applications in retail stores, grocery stores, light warehouses, repair garages, maintenance storage, business office storage and residential storage. Reinforced brackets lock into slotted standards for strong, secure weight-bearing support. Fully adjustable in 1 in increments. 16 ga cold rolled steel...

High-strength steel 36 in mortise-mount pilaster standard features 1/2 in vertical slot adjustability and countersunk nail, screw and staple holes. Numbered slots provide quick, accurate clip...

High-strength steel 36 in mortise-mount pilaster standard features 1/2 in vertical slot adjustability and countersunk nail, screw and staple holes. Numbered slots provide quick, accurate clip insertion. System holds up to 500 lb per shelf when properly installed. Can be installed on the surface or made flush with the wall or cabinet by making a dado cut.Unit: EA

For use with the 80 Series standards. For shelving applications in light industrial, commercial and residential use. Standards can be mounted to nearly any type of wall. For storage and display...

For use with the 80 Series standards. For shelving applications in light industrial, commercial and residential use. Standards can be mounted to nearly any type of wall. For storage and display applications in retail stores, grocery stores, light warehouses, repair garages, maintenance storage, business office storage and residential storage. Reinforced brackets lock into slotted standards for strong, secure weight-bearing support. Fully adjustable in 1 in increments. 16 ga cold rolled steel...

Double-lug bracket design prevents shelves and contents from falling when bumped. Supports adjust to accommodate changes in storage and layout. Rounded corners and recessed groove design. Cover...

Double-lug bracket design prevents shelves and contents from falling when bumped. Supports adjust to accommodate changes in storage and layout. Rounded corners and recessed groove design. Cover strips conceal screw holes and slots for a more refined appearance. Epoxy finish is resistant to chips and scratches.Unit: EA

Screws are 1-1/2 in long with a #8 body and #6 head.Unit: BAG 6

Screws are 1-1/2 in long with a #8 body and #6 head.Unit: BAG 6

Optional rear mounting socket for face frame application simplifies installation. Non-handed. Hardware included. 3-1/2 in L x 1/2 in W. Zinc finish.Unit: EA

Optional rear mounting socket for face frame application simplifies installation. Non-handed. Hardware included. 3-1/2 in L x 1/2 in W. Zinc finish.Unit: EA