WATTS

This 1/2 in hot water extender tempering valve is designed for domestic water supply systems and recommended for tankless heater, water heater and solar applications installed at or near the boiler...

This 1/2 in hot water extender tempering valve is designed for domestic water supply systems and recommended for tankless heater, water heater and solar applications installed at or near the boiler or hot water heater. It consists of a lead-free brass body, solder connections, thermostat, stainless steel springs and dial adjustment cap. The hydraulically operated thermostat opens a spring loaded check in the cold water inlet which allows cold and hot water to mix and can be replaced as a unit....

Connection shall be made using Watts series 35 quick-connect fitting with integral collet and O-ring guide. Fitting shall be able to fully rotate under pressure and allow for easy disconnect and...

Connection shall be made using Watts series 35 quick-connect fitting with integral collet and O-ring guide. Fitting shall be able to fully rotate under pressure and allow for easy disconnect and re-use without the use of disconnection tools. Fitting must not disassemble to disconnect.Unit: BAG

Watts Quick-connect valves are designed and manufactured for many years of trouble-free service. Produced of off white polysulfone, a high-performance thermal plastic material. The Watts...

Watts Quick-connect valves are designed and manufactured for many years of trouble-free service. Produced of off white polysulfone, a high-performance thermal plastic material. The Watts quick-connect design allows for quick and easy connections without the use of installation tools.Unit: BAG

Connection shall be made using Watts series 35 quick-connect fitting with integral collet and O-ring guide. Fitting shall be able to fully rotate under pressure and allow for easy disconnect and...

Connection shall be made using Watts series 35 quick-connect fitting with integral collet and O-ring guide. Fitting shall be able to fully rotate under pressure and allow for easy disconnect and re-use without the use of disconnection tools. Fitting must not disassemble to disconnect.Unit: BAG

Connects to copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing.Unit: BAG 1

Connects to copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing.Unit: BAG 1

This 3/4 in lead-free hot water control valve is designed for installation on water heating equipment to provide tempered water to point-of-use fixtures and is ideal for radiant heat applications....

This 3/4 in lead-free hot water control valve is designed for installation on water heating equipment to provide tempered water to point-of-use fixtures and is ideal for radiant heat applications. The double throttling design combines hot and cold water control for a sensitive response to water temperature changes in the mixing chamber. It consists of a lead-free brass body, threaded union connections, solid wax hydraulic principle thermostat, integral filter washers and check valves, virtual...

Highly corrosion-resistant. Unaffected by salts and caustic fluids. All injection molded polyethylene construction. Resistant to sunlight deterioration. Maximum temperature 140 deg F.Unit: EA ...

Highly corrosion-resistant. Unaffected by salts and caustic fluids. All injection molded polyethylene construction. Resistant to sunlight deterioration. Maximum temperature 140 deg F.Unit: EA

Watts quick-connect connectors are designed and manufactured for many years of trouble-free service. Produced of off-white polysulfone, a high-performance thermal plastic material, the Watts...

Watts quick-connect connectors are designed and manufactured for many years of trouble-free service. Produced of off-white polysulfone, a high-performance thermal plastic material, the Watts quick-connect design allows for quick and easy connections without the use of installation tools.Unit: EA

Watts Tube Union Coupling, Nominal Size: 1 in, PlasticUnit: BAG 1

Watts Tube Union Coupling, Nominal Size: 1 in, PlasticUnit: BAG 1

Works with copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing in hot and cold water applications. Incorporates stainless steel gripping teeth in the collets, allowing the connectors to...

Works with copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing in hot and cold water applications. Incorporates stainless steel gripping teeth in the collets, allowing the connectors to interconnect with multiple materials without special tools or tube inserts. Exclusive O-ring guide insures zero-leak connections. Tube orientation can be changed by a simple twist, reducing the amount of tubing required to plumb a water system. Reusable, approved for use behind walls and underground....

Series ST1250 standard duty mechanical float valves are used in commercial, industrial and agricultural applications for controlling water flow. It has a bronze body construction with 1-1/4 in...

Series ST1250 standard duty mechanical float valves are used in commercial, industrial and agricultural applications for controlling water flow. It has a bronze body construction with 1-1/4 in female NPT threaded end connections, cotter pin pivot arm assembly, replaceable seals and replaceable plungers. This Series is ideal for use in air conditioning, refrigeration and irrigation systems.Unit: EA

Eliminates the need for additional fittings. Produced of polysulfone, a high performance thermal plastic material, this manifold is designed for years of trouble-free service. The design allows for...

Eliminates the need for additional fittings. Produced of polysulfone, a high performance thermal plastic material, this manifold is designed for years of trouble-free service. The design allows for quick and easy installation without the use of additional tools.Unit: BAG 1

Allows ball to float free. Designed for use on exposed cattle watering systems. Cattle can nuzzle ball without harm to or activation of valve. Assembly consists of thumb screw, hooks, swivel joint...

Allows ball to float free. Designed for use on exposed cattle watering systems. Cattle can nuzzle ball without harm to or activation of valve. Assembly consists of thumb screw, hooks, swivel joint and stem threaded at one end.Unit: EA

Plastic quick-connect fittings are made from polysulfone, a high-performance thermal plastic material. Design allows for quick and easy connections to pipe without installation tool. Use on copper,...

Plastic quick-connect fittings are made from polysulfone, a high-performance thermal plastic material. Design allows for quick and easy connections to pipe without installation tool. Use on copper, PEX, CPVC and polybutylene pipe. Product meets all National Plumbing Codes.Unit: EA

Used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 Btu/hr. Features a...

Used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 Btu/hr. Features a bronze body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating and a test lever. ASME rated and CSA listed. Temperature relief is 210 deg F (99 deg C), Pressure relief range is 75 to 150psi (5.2 to 10.3 bar).Unit: EA

This quick-connect elbow fitting is designed for use in potable water applications. It is made of polysulfone plastic and is tested, certified and approved for drinking water. This 3/8 in CTS...

This quick-connect elbow fitting is designed for use in potable water applications. It is made of polysulfone plastic and is tested, certified and approved for drinking water. This 3/8 in CTS fitting rotates fully under pressure, connects to multiple materials without the use of installation tools and features an integral collet with stainless steel gripping teeth and patented O-ring guide design. The pressure rating is 100 psi at 180 deg F (6.9 bar at 82 deg C) or 250 psi at 75 deg F (17.2...

Watts quick-connect connectors are designed and manufactured for many years of trouble-free service. Produced of off-white polysulfone, a high-performance thermal plastic material, the Watts...

Watts quick-connect connectors are designed and manufactured for many years of trouble-free service. Produced of off-white polysulfone, a high-performance thermal plastic material, the Watts quick-connect design allows for quick and easy connections without the use of installation tools.Unit: BAG

Used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 Btu/hr. Features a...

Used in water heater and hot water storage tank applications to provide automatic temperature and pressure protection to hot water supply tanks and hot water heaters up to 105,000 Btu/hr. Features a bronze body with NPT male inlet and NPT female outlet connections, unique thermostat with special thermo-bonded coating and a test lever. ASME rated and CSA listed. Temperature relief is 210 deg F (99 deg C), pressure relief range is 75 to 150psi (5.2 to 10.3 bar).Unit: EA

Sea Tech 35 Series products are designed and manufactured to be trouble-free for many years of service life. 35 Series products are designed and manufactured in polysulfone, a high-performance...

Sea Tech 35 Series products are designed and manufactured to be trouble-free for many years of service life. 35 Series products are designed and manufactured in polysulfone, a high-performance thermal plastic material. 35 Series products are available in standard imperial inch sizes and interconnect with all Sea Tech 24 Series fittings. The Sea Tech quick-connect design allows for quick and easy connections without installation tools. Simply cut the plastic, copper or CPVC piping and snap a...

Watts quick-connect connectors are designed and manufactured for many years of trouble-free service. Produced of off-white polysulfone, a high-performance thermal plastic material, the Watts...

Watts quick-connect connectors are designed and manufactured for many years of trouble-free service. Produced of off-white polysulfone, a high-performance thermal plastic material, the Watts quick-connect design allows for quick and easy connections without the use of installation tools.Unit: BAG

Incorporates stainless steel gripping teeth in the collets. These corrosion-resistant teeth allow the connectors to interconnect with multiple materials without the need for special tools or tube...

Incorporates stainless steel gripping teeth in the collets. These corrosion-resistant teeth allow the connectors to interconnect with multiple materials without the need for special tools or tube inserts. It works with copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing.Unit: BAG 1

Works with copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing in hot and cold water applications. Incorporates stainless steel gripping teeth in the collets, allowing the connectors to...

Works with copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing in hot and cold water applications. Incorporates stainless steel gripping teeth in the collets, allowing the connectors to interconnect with multiple materials without special tools or tube inserts. Exclusive O-ring guide insures zero-leak connections. Tube orientation can be changed by a simple twist, reducing the amount of tubing required to plumb a water system. Reusable, approved for use behind walls and underground....

Plastic quick-connect fittings are made from polysulfone, a high-performance thermal plastic material. Design allows for quick and easy connections to pipe without installation tool. Use on copper,...

Plastic quick-connect fittings are made from polysulfone, a high-performance thermal plastic material. Design allows for quick and easy connections to pipe without installation tool. Use on copper, PEX, CPVC and polybutylene pipe. Product meets all National Plumbing Codes.Unit: EA

This 3/8 in x 1/2 in plastic quick-connect elbow incorporates stainless steel gripping teeth in the collets. These corrosion-resistant teeth allow the connectors to interconnect with multiple...

This 3/8 in x 1/2 in plastic quick-connect elbow incorporates stainless steel gripping teeth in the collets. These corrosion-resistant teeth allow the connectors to interconnect with multiple materials without the need for special tools or tube inserts. It works with copper, CPVC, PEX, LPDE, MPDE, HDPE and polybutylene tubing.Unit: EA