SELKIRK

Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed...

Used wherever a ceiling support, finish support, firestop or joist shield is installed below an open attic. Required to guard against the hazard of blown-in or blanket insulation filling any framed opening or contacting the chimney and possible storage of combustibles against the chimney.Unit: EA

Selkirk Elbow, 5 in Connection, Galvanized Steel, Dimensions: 8-1/4 in L x 5-1/2 in W x 8-3/4 in H, Suitable for: Type B Gas VentUnit: EA

Selkirk Elbow, 5 in Connection, Galvanized Steel, Dimensions: 8-1/4 in L x 5-1/2 in W x 8-3/4 in H, Suitable for: Type B Gas VentUnit: EA

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. In the Sure-Temp-Type HT...

Part of the chimney system roof assembly, the round top is designed with a dome to exclude rain and leaves and a lower skirt to deflect wind for proper chimney draft. In the Sure-Temp-Type HT Chimney (5 in, 6 in, 7 in and 8 in sizes) the round top is designed with three legs that slide down over the outside of the chimney. A cinch band is then positioned over the legs and tightened to hold the top firmly in place. This design makes cap removal for cleaning a breeze.Unit: EA

For pellet and corn appliances. Kit contains 3 in horizontal cap, 3 in 90 deg elbow, 3 in wall bracket, five 3 in 1 ft pipe lengths, 3 in tee with cleanout, 3 in wall thimble and 3 in pipe...

For pellet and corn appliances. Kit contains 3 in horizontal cap, 3 in 90 deg elbow, 3 in wall bracket, five 3 in 1 ft pipe lengths, 3 in tee with cleanout, 3 in wall thimble and 3 in pipe connector. System rated for flue temperatures up to 570 deg. Proven coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Inner wall is 304 stainless steel, outer wall is paintable galvanized. Rolled-over male end eliminates sharp edges. 1 in clearance to combustibles....

Type L air insulated pellet vent tee with cap designed for use in changing the orientation of the vent from horizontal to vertical and making inspection and cleaning of pellet stove system easier....

Type L air insulated pellet vent tee with cap designed for use in changing the orientation of the vent from horizontal to vertical and making inspection and cleaning of pellet stove system easier. UL listed.Unit: EA

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for...

Provides a secure attachment for the chimney to smoke chamber outlet on masonry fireplaces, reducing footing loads and speeding construction. Stainless steel and heavy-gauge steel construction for long life. Retains chimney with a twist-lock connection.Unit: EA

Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a locking band, to pass safely...

Used to start chimneys indoors or outdoors using a wall support assembly or a masonry pier. A length of insulated chimney pipe is attached to the Tee snout, using a locking band, to pass safely through combustible walls. An insulated tee cap is included which can be removed from bottom opening for inspection and cleanout. Maximum height of chimney which can be supported by an insulated Tee is 50 ft.Unit: EA

Selkirk SURE-TEMP Insulated Thimble, Wall MountingUnit: EA

Selkirk SURE-TEMP Insulated Thimble, Wall MountingUnit: EA

Diamond shaped 1/2 in x 1 in mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.Unit: EA

Diamond shaped 1/2 in x 1 in mesh, 18-8 stainless steel. Fits same size round chimney top. Keeps foreign objects out of chimney.Unit: EA

Can be used for fixed offsets of 15 deg slope or in pairs for offsets adjustable from zero to 30 deg slope. Greater angles are prohibited by UL standard 103 and by the terms of the product listing....

Can be used for fixed offsets of 15 deg slope or in pairs for offsets adjustable from zero to 30 deg slope. Greater angles are prohibited by UL standard 103 and by the terms of the product listing. Required locking bands (2 packaged with each elbow kit) allow 360 deg rotation and lock the components together in place at the exact offset required. Insulated elbows can be used at the same 2 in air space clearance as chimney sections. Includes 2 elbows, 2 locking bands and interior...

Selkirk Drip less Smoke Stove Pipe Adapter, 316 Stainless Steel, Dimensions: 15-3/4 In LUnit: EA

Selkirk Drip less Smoke Stove Pipe Adapter, 316 Stainless Steel, Dimensions: 15-3/4 In LUnit: EA

Includes finishing band. Easily removable for inspection and cleaning. Eliminates the need to cut pipe. For installed length, subtract 1-3/8 in per joint. Adjustable 38 to 68 in length.Unit: EA ...

Includes finishing band. Easily removable for inspection and cleaning. Eliminates the need to cut pipe. For installed length, subtract 1-3/8 in per joint. Adjustable 38 to 68 in length.Unit: EA

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern,...

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only. The SCS is usable on any appliance having a power burner (such as an oil furnace) if that appliance operates with neutral or negative draft at its outlet.Unit: EA

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow....

Used whenever there is a need to stabilize the chimney above the roof level. The purpose of the bracing is to hold the chimney against wind load and to prevent damage from static and sliding snow. It should be used, at a midpoint on the chimney. Bracket adjusts from 4 to 6 ft.Unit: EA

Interior resupport assembly allows for two different methods of chimney resupport. The first method is used at the immediate section of chimney above the upper elbow of an offset. With the...

Interior resupport assembly allows for two different methods of chimney resupport. The first method is used at the immediate section of chimney above the upper elbow of an offset. With the appropriate fire stop/joist shield (JS) in place, clamp the support band around chimney and attach with six-sheet metal screws. The second means of support is used primarily when the immediate sections of the upper offset do not pass through a joist area and resupport is necessary. The support band is...

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern,...

The Selkirk Chimney System (SCS) is ideal for venting residential heating appliances burning wood, 2-oil and natural and LP gas. They have been specifically designed for today's modern, high-efficiency "airtight" wood stoves. They are designed for gravity (natural draft), non-positive internal pressure venting only. The SCS is usable on any appliance having a power burner (such as an oil furnace) if that appliance operates with neutral or negative draft at its outlet.Unit: EA

Exit cone cap is designed to direct flue gases perpendicular to the wall and to increase their velocity, projecting them further away from the building. UL listed.Unit: EA

Exit cone cap is designed to direct flue gases perpendicular to the wall and to increase their velocity, projecting them further away from the building. UL listed.Unit: EA

Unidirectional twin reverse cone works in all weather conditions, hot or cold. Protects from wind and rain during cold chimney conditions. Ensures normal flow during windy conditions.Unit: EA ...

Unidirectional twin reverse cone works in all weather conditions, hot or cold. Protects from wind and rain during cold chimney conditions. Ensures normal flow during windy conditions.Unit: EA

Can be used for fixed offsets of 30 deg slope. Greater angles are prohibited by UL Standard 103 and by the terms of the product listing. Required Locking bands (2 packaged with each elbow kit) are...

Can be used for fixed offsets of 30 deg slope. Greater angles are prohibited by UL Standard 103 and by the terms of the product listing. Required Locking bands (2 packaged with each elbow kit) are to be used at each joint. Each offset must be resupported. Elbows rotate 360 deg to provide the exact orientation required. Insulated elbows can be used at the same 2 ft air space clearance as chimney sections. Kit includes 2 elbows, 2 locking bands and one interior resupport.Unit: EA

Unidirectional twin reverse cone works in all weather conditions, hot or cold. Protects from wind and rain during cold chimney conditions. Ensures normal flow during windy conditions.Unit: EA ...

Unidirectional twin reverse cone works in all weather conditions, hot or cold. Protects from wind and rain during cold chimney conditions. Ensures normal flow during windy conditions.Unit: EA

Used to conceal the crimped end on the last length in the system.Unit: EA

Used to conceal the crimped end on the last length in the system.Unit: EA

Selkirk Bird Proof Round TopUnit: EA

Selkirk Bird Proof Round TopUnit: EA

Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread...

Prevents or delays the rapid spread of fire (regardless of the cause) in a home or building. The sheet metal firestop prevents the chimney passageway from becoming an easy pathway for fire to spread from one floor to another.Unit: EA

For pellet and corn appliances. Kit contains 4 in horizontal cap, 4 in 90 deg elbow, 4 in wall bracket, five 4 in 1 ft pipe lengths, 4 in tee with cleanout, 4 in wall thimble, 4 in tee support, 3 to...

For pellet and corn appliances. Kit contains 4 in horizontal cap, 4 in 90 deg elbow, 4 in wall bracket, five 4 in 1 ft pipe lengths, 4 in tee with cleanout, 4 in wall thimble, 4 in tee support, 3 to 4 in pellet increaser, 4 in pipe connector and 3 in pipe connector. System rated for flue temperatures up to 570 deg. Proven coupling joint connects in seconds to assure joint integrity. Gasketed joint design. Inner wall is 304 stainless steel, outer wall is paintable galvanized. Rolled-over male...